- #Azurewave wifi software aw ne769 how to#
- #Azurewave wifi software aw ne769 password#
- #Azurewave wifi software aw ne769 download#
#Azurewave wifi software aw ne769 password#
Password: password for AP (case sensitive) security type: OPEN | WEP | WPA | WPA2 Step 2: Check if AW-CU427-USB is in station mode using AT+WIFI_GetMode Step 3: Set and store information of the AP using AT+WIFI_SetAP= Module of the AW-CU427-USB using AT+WIFI_On Wireless devices near the AW-CU427-USB (except for the device under test). Step 1: Connect the AW-CU427-USB to the system (refer to 2. Assume the SSID, password and security type of the AP is MySSID, MyPassword, Step 0: Make sure the AP under test is connected to the internet using other Wi-Fi enabledĭevices.
(12)ģ.2 Publish and Monitor MQTT message on the cloud Because they will be used when sending the AT+THING_Set command.
#Azurewave wifi software aw ne769 download#
In Create and activate a device certificate chapter, please download and keep the certificate and Please refer to the steps at the following link.Īfter finishing the steps, please notice the following two actions: After provisioning, you can connect to AWS IOT Parameter will be provision to our connector. You can use certificate, private key, thing nameĪnd endpoint as AT+THING_Set command parameter. This step will create certificate and private key. Please refer to the following link to create a thing. Policies (AmazonFreeRTOSFullAccess, AWSIoTFullAccess) to your IAM.Ī thing represents a specific device or instance that can communicate with AWS IOT. If you have created an IAM user, please refer to the following setting to connect these two Please refer to the below link to setup AWS Account and IAM user. Step 1: Create AWS Account, Create an IAM user.
#Azurewave wifi software aw ne769 how to#
Step 0: The below link is a documents of how to setup AWS IOT, you can refer to it for full AWSīut, if you want to setup AzureWave AWS Connector, you would just refer to the following steps. Subscribe to and save MQTT topic: AT+MQTT_Subscribe=,ĪT+MQTT_Publish=topic,message,qos topic: Topic to publish to Connect the client to MQTT broker: AT+MQTT_ConnectĨ. Define and store Thing-specific configuration:ĪT+THING_Set=client ID,endpoint,client certificate,client private key client ID: Thing name(Client ID)Ĭlient certificate: Certificate for this Thing client private key: Private key for this Thingħ. Password: password for AP (case sensitive) security type: OPEN | WEP | WPA | WPA2 5. Set and store the Wi-Fi AP information when AW-CU427-USB in Station Mode:ĪT+WIFI_SetAP=SSID,password,security type SSID: SSID of AP (case sensitive) Perform a Wi-Fi network scan: AT+WIFI_ScanĤ.
Retrieve the Wi-Fi AP | Station Mode: AT+WIFI_GetMode 3. Please find the command details in AWS CONNECTOR AT Command Set.Ģ. Steel Desk & Chair + Horizontal Position + Close to Desk Edge Steel Desk & Chair + Horizontal Position The examples below are antenna radiation patterns with different setups: If not, adjust the setup until the RSSI >-65dBm. Strength Indication) is good (>-65dBm) or not. Use AT command AT+WIFI_On and AT+WIFI_Scan to check if the RSSI (Received Signal Minimum clearance is 20mm for conductive materials and 10mm for non-conductive materials.įailing to meet the clearance requirements will detune the antenna and the radiation pattern may This can be a problem if those objects are electrically large. Objects close to the antenna (the dongle) become new sources for radiation from far field The AW-CU427-USB includes an integrated omnidirectional antenna. The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of AzureWave.